Copyright Tomi Engdahl 1997
Sometimes it is necessary to connect a device which has only speaker outputs to external amplifier's line level inputs. Because speaker levels are much higher than line level signals, the direct connection does not usually give satisfactory results. That's the reason why I developed this signal level attenuator for connecting speaker signals to line level inputs without signal level problems.
The circuit is designed to work with typical HIFI amplifiers where negative speaker connector (black) is connected to amplifier ground. Be careful here because some modern amps have both terminals actively driven. Connecting either one to a common reference could cause the output stage to smoke.
The circuit is suitable to be used with 1..50W audio amplifers. The circuit is connected to the speaker output of the amplifier and can be used in parallel with the existing speakers.
Suitability for amplifiers: 1..50W
Signal attenuation: 20 dB
Input impedance: 10 kohm
Output impedance: 1 kohm
Frequency response: flat from 20 Hz to 20 kHz
Speaker level signals are usually in 3..20V range (amplifiers up to 50W output power). The line level signals should be in 0.3..2V range to be suitable for amplifier's line level input. So attenuation of about 20 dB is needed to bring the signals to right level. This conversion can be done easily using 10:1 voltage divider circuit.
The circuit below is a resistor voltage divider circuit which just does about 10:1 voltage attenuation. Input impedance of the circuit is about 10 kohm, so it does not load the amplifier driving it in any significant way and can be used in parallel with existing speakers without any problems. The output impedance of the circuit is about 1 kohm, which is well suitable for normal line inputs.
Remember to check that the circuit is connected in the right way every time you use it. If you mix up speaker out and speaker ground connection, you can end up shorting speaker output to ground, which can damage your amplifier and/or other equipment connected to it. If you want to redice the risk of damaging anythign then put 10 ohm resistor between the circuit and speaker ground connector (this will make sure that short circuit impedance is always at least 10 ohms, though it can introduce sometime hummign problems because of increase grounding impendace).
Remember that this circuit is designed only to be used with normal amplifiers which have common ground for speaker signals. It is not suitable to be used with bridge type output car stereo amplifiers.
If you are planning to use thie circuit with amplifier where there are no spakers connected to them some amplifiers might have poower sound quality if there is nothign connected to speaker output. If you experience this kind of problem, then you can put a 8 ohm resistor (or whatever the apaker impedance that amplifier normally runs is) and use it as a load. Remeber to select a resistor which cna handle the power that the amplifier output. If you want to get around using a lower power resistor, then usually a resistor in 50-300 ohm range gives satisfactory results (instead of nominal 8 ohm). Anyway in most cases you don't need this kind of loading resistors.
If you want to adjust the output level then replace R2 with 1 kohm trimmer. This makes it possible to make the output level to be adjustable from 0V to line level.
If you want to use the circuit safely with more powerful amplifiers than 50W, then you have to modufy the circuit to give more attenuation. This can be easily done by changing the value of R1 to 33 kohm. This makes the attenuation to be 33:1 (around 30 dB). With this attenuation the circuit is usable to amplifiers up to about 300W. Remember to construct the circuit very carefully if you are going to use it with those high power amplifiers because the voltage on their speaker lines are at dangerous levels at high sound levels.
Simple resistor attenuator is very useful also in many other applications than just the speaker level to line level converters.
XLR 2 ----50k-----------+---- TIP | 3 --+ 5k | | 1 --+---------------+------ SLEEVE
Modern Hifi-VHS VCRs don't typically have automatic level adjustment or manula adjustment of recording levels. The dynamics of the HiFi-VHS video soundtrack is so large that the adjustments are quite often unnecessary. But in some cases some satellite boxes output higher than the pecs say signals and if they are connected to HiFi-VHS video the sound can distort in largest signals. To avoid this you can use the following small attenuator in the HiFi VCR audio connections (you need one for left audio channel and one for right channel and you can built the circuit inside SCART EURO-AV connector if you equipments are connected together using them).
SIGNAL >----2k2----------+----> SIGNAL | 2k2 | GROUND ------------------+----- GROUND